Difference between revisions of "Palawan DVT"

From Studio Kousagi Wiki
Jump to: navigation, search
Line 4: Line 4:
  
 
* '''ECO1''': The LED is backwards, and should be flipped around.
 
* '''ECO1''': The LED is backwards, and should be flipped around.
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA12.
+
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA11.
 
* '''ECO3''': There is a ground (and power) plane directly under the RFM69HW.  This should be pulled back.
 
* '''ECO3''': There is a ground (and power) plane directly under the RFM69HW.  This should be pulled back.
 
* '''ECO4''': The LP3982 footprint has no "Pin 1" marker.  Add a Pin 1 marker.
 
* '''ECO4''': The LP3982 footprint has no "Pin 1" marker.  Add a Pin 1 marker.
 
* '''ECO5''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.
 
* '''ECO5''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.
 +
* '''ECO6''': The board is four layers.  This is unnecessary.  Make the board two layers.
 +
* '''ECO7''': The "Pair" button is not connected to a pin that can do ADC or IRQ.  Move "Pair" to PTA12.
  
 
==Palawan Tx ECOs==
 
==Palawan Tx ECOs==
  
 
* '''ECO1''': There is a stray via on the board.  Run DRC prior to exporting to gerbers to repour copper.
 
* '''ECO1''': There is a stray via on the board.  Run DRC prior to exporting to gerbers to repour copper.
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA12.
+
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA11.
 
* '''ECO3''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.
 
* '''ECO3''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.

Revision as of 08:30, 10 June 2017

Palawan DVT represents a complete redesign. The main MCU has changed, and we now use a SoM for the radio.

Palawan Rx ECOs

  • ECO1: The LED is backwards, and should be flipped around.
  • ECO2: RFM69HW DIO0 is connected to a pin that cannot generate an interrupt. Move DIO0 to PTA11.
  • ECO3: There is a ground (and power) plane directly under the RFM69HW. This should be pulled back.
  • ECO4: The LP3982 footprint has no "Pin 1" marker. Add a Pin 1 marker.
  • ECO5: The KL02 footprint has a non-obvious "Pin 1" marker. Make it clearer.
  • ECO6: The board is four layers. This is unnecessary. Make the board two layers.
  • ECO7: The "Pair" button is not connected to a pin that can do ADC or IRQ. Move "Pair" to PTA12.

Palawan Tx ECOs

  • ECO1: There is a stray via on the board. Run DRC prior to exporting to gerbers to repour copper.
  • ECO2: RFM69HW DIO0 is connected to a pin that cannot generate an interrupt. Move DIO0 to PTA11.
  • ECO3: The KL02 footprint has a non-obvious "Pin 1" marker. Make it clearer.