Difference between revisions of "Palawan DVT"

From Studio Kousagi Wiki
Jump to: navigation, search
 
(4 intermediate revisions by the same user not shown)
Line 3: Line 3:
 
==Palawan Rx ECOs==
 
==Palawan Rx ECOs==
  
* '''ECO1''': The LED is backwards, and should be flipped around.
+
* '''ECO1''': The LED footprint and schematic symbol have mismatched leads, and should be flipped around.
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA12.
+
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA10.
 
* '''ECO3''': There is a ground (and power) plane directly under the RFM69HW.  This should be pulled back.
 
* '''ECO3''': There is a ground (and power) plane directly under the RFM69HW.  This should be pulled back.
 
* '''ECO4''': The LP3982 footprint has no "Pin 1" marker.  Add a Pin 1 marker.
 
* '''ECO4''': The LP3982 footprint has no "Pin 1" marker.  Add a Pin 1 marker.
 
* '''ECO5''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.
 
* '''ECO5''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.
 +
* '''ECO6''': The board is four layers.  This is unnecessary.  Make the board two layers.
 +
* '''ECO7''': The "Pair" button is not connected to a pin that can do ADC or IRQ.  Move "Pair" to PTB7.
 +
* '''ECO8''': The LED is not hooked up to a pin that can do PWM.  Move LED to PTA12.
 +
* '''ECO9''': It is unclear whether code is running on Tx or Rx.  Change R101 from 22k to 2.2k.
 +
* '''ECO10''': The ESD diode's footprint and schematic symbol have swapped leads.  Swap the pin number mapping.
  
 
==Palawan Tx ECOs==
 
==Palawan Tx ECOs==
  
 
* '''ECO1''': There is a stray via on the board.  Run DRC prior to exporting to gerbers to repour copper.
 
* '''ECO1''': There is a stray via on the board.  Run DRC prior to exporting to gerbers to repour copper.
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA12.
+
* '''ECO2''': RFM69HW DIO0 is connected to a pin that cannot generate an interrupt.  Move DIO0 to PTA10.
 
* '''ECO3''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.
 
* '''ECO3''': The KL02 footprint has a non-obvious "Pin 1" marker.  Make it clearer.
 +
* '''ECO4''': All diodes have their schematic/pcb footprint pins swapped.  Fix this.
 +
* '''ECO5''': Through-holes are not .1" spacing.  See if it isn't possible to fix this.
 +
 +
 +
Pins:
 +
  PAIR - IRQ, ADC (PTB7 is the only match)
 +
  LED - High-current, PWM (PTA12 is the only match)
 +
  DIO0 - IRQ (PTA10 is closest)

Latest revision as of 01:22, 20 June 2017

Palawan DVT represents a complete redesign. The main MCU has changed, and we now use a SoM for the radio.

Palawan Rx ECOs

  • ECO1: The LED footprint and schematic symbol have mismatched leads, and should be flipped around.
  • ECO2: RFM69HW DIO0 is connected to a pin that cannot generate an interrupt. Move DIO0 to PTA10.
  • ECO3: There is a ground (and power) plane directly under the RFM69HW. This should be pulled back.
  • ECO4: The LP3982 footprint has no "Pin 1" marker. Add a Pin 1 marker.
  • ECO5: The KL02 footprint has a non-obvious "Pin 1" marker. Make it clearer.
  • ECO6: The board is four layers. This is unnecessary. Make the board two layers.
  • ECO7: The "Pair" button is not connected to a pin that can do ADC or IRQ. Move "Pair" to PTB7.
  • ECO8: The LED is not hooked up to a pin that can do PWM. Move LED to PTA12.
  • ECO9: It is unclear whether code is running on Tx or Rx. Change R101 from 22k to 2.2k.
  • ECO10: The ESD diode's footprint and schematic symbol have swapped leads. Swap the pin number mapping.

Palawan Tx ECOs

  • ECO1: There is a stray via on the board. Run DRC prior to exporting to gerbers to repour copper.
  • ECO2: RFM69HW DIO0 is connected to a pin that cannot generate an interrupt. Move DIO0 to PTA10.
  • ECO3: The KL02 footprint has a non-obvious "Pin 1" marker. Make it clearer.
  • ECO4: All diodes have their schematic/pcb footprint pins swapped. Fix this.
  • ECO5: Through-holes are not .1" spacing. See if it isn't possible to fix this.


Pins:

 PAIR - IRQ, ADC (PTB7 is the only match)
 LED - High-current, PWM (PTA12 is the only match)
 DIO0 - IRQ (PTA10 is closest)