Difference between revisions of "DIY Plastics Kit"

From Studio Kousagi Wiki
Jump to: navigation, search
(Contents)
(Added new step 2 for manually upgrading the firmware.)
Line 20: Line 20:
 
[[File:Mainboard to case.jpg | 600px]]
 
[[File:Mainboard to case.jpg | 600px]]
  
===Step 2: Antenna Attachment===
+
===Step 2: Update Firmware===
 +
 
 +
The NeTV ships with firmware version 25 on the microSD card. There have been reports that the automatic firmware update is problematic. It will be much easier to upgrade the firmware manually '''before''' you continue the rest of the assembly. Remove the microSD, [http://bunniefoo.com/netv/rom-chumby-silvermoon-netv-chumby-image-r43.zip download the latest firmware image], and follow the steps to [https://kosagi.com/w/index.php#Burning_images_to_disk burn the image to disk].
 +
 
 +
[[File:NeTV-SD-location.jpg|400px||Location of the SD card]]
 +
 
 +
===Step 3: Antenna Attachment===
 
Peel the adhesive tape off of the back of the wifi antenna, and attach the antenna to the top case, paying attention to the following important rules:
 
Peel the adhesive tape off of the back of the wifi antenna, and attach the antenna to the top case, paying attention to the following important rules:
  
Line 35: Line 41:
 
Despite the strong warnings, you won't damage anything if you mount the antenna incorrectly; you will simply have non-optimal RF performance.
 
Despite the strong warnings, you won't damage anything if you mount the antenna incorrectly; you will simply have non-optimal RF performance.
  
===Step 3: Snap Case Together===
+
===Step 4: Snap Case Together===
 
Before starting this step, take a moment to observe that the inner plastic wall of the "HD video in" port has grooves designed to enable the HDMI connector to slide against the plastic wall. Note that the opposite "HD video out" port lacks these grooves.  
 
Before starting this step, take a moment to observe that the inner plastic wall of the "HD video in" port has grooves designed to enable the HDMI connector to slide against the plastic wall. Note that the opposite "HD video out" port lacks these grooves.  
  
Line 50: Line 56:
 
Note that if you reverse the assembly order of the sides, you will apply a traumatic amount of stress to the HD video out connector and the IR extender connector.
 
Note that if you reverse the assembly order of the sides, you will apply a traumatic amount of stress to the HD video out connector and the IR extender connector.
  
===Step 4: Affix Retaining Screws ===
+
===Step 5: Affix Retaining Screws ===
 
Use the remaining screws to fix the two halves of the case together. If you intend to take the unit apart fairly often, you may omit the screws, as the HDMI connectors and snap hooks do a pretty good job of holding the case together and planarizing the assembly.
 
Use the remaining screws to fix the two halves of the case together. If you intend to take the unit apart fairly often, you may omit the screws, as the HDMI connectors and snap hooks do a pretty good job of holding the case together and planarizing the assembly.
  
 
[[File:Fourblack screws.jpg | 600px]]
 
[[File:Fourblack screws.jpg | 600px]]
  
===Step 5: Affix the Rubber Foot===
+
===Step 6: Affix the Rubber Foot===
 
Peel the backing off of the rubber foot and attach.  
 
Peel the backing off of the rubber foot and attach.  
  
 
[[File:Attach foot.jpg | 600px]]
 
[[File:Attach foot.jpg | 600px]]
  
===Step 6: Remove Anti-Fingerprint Wrap===
+
===Step 7: Remove Anti-Fingerprint Wrap===
 
If you haven't done so, remove the anti-fingerprint wraps. It is strongly recommend that you do this because otherwise the cooling holes on the top of the case are obstructed.
 
If you haven't done so, remove the anti-fingerprint wraps. It is strongly recommend that you do this because otherwise the cooling holes on the top of the case are obstructed.

Revision as of 20:00, 14 October 2016

Out of the box

Out of the box, the DIY kit is a compact, bubble-wrapped set of parts.

Diy kit packaged.jpg

Contents

The kit should contain the following contents:

  • A card pointing to this URL
  • The top of the plastic case
  • The base of the plastic case
  • A rubber foot for the plastic case
  • Four long screws (PB2.3x8mm self-tapping cross head screw)
  • Four short screws (PB2.3x4mm self-tapping cross head screw)

Diy kit overview.jpg

Step 1: Mainboard Attachment

Attach the mainboard to the case using the four short screws.

Mainboard to case.jpg

Step 2: Update Firmware

The NeTV ships with firmware version 25 on the microSD card. There have been reports that the automatic firmware update is problematic. It will be much easier to upgrade the firmware manually before you continue the rest of the assembly. Remove the microSD, download the latest firmware image, and follow the steps to burn the image to disk.

Location of the SD card

Step 3: Antenna Attachment

Peel the adhesive tape off of the back of the wifi antenna, and attach the antenna to the top case, paying attention to the following important rules:

  • The antenna must be on the side of the case with the HDMI ports (the side without the word "bunnie" on it)
  • The antenna must be kept as flat as possible (do not wrinkle the membrane as you apply it)
  • The antenna should be as close to the case edge as possible without curving the antenna itself

The active element of the antenna is a thin strip about 1cm wide near the outer edge. The case is designed to ensure the active elements clear the HD video ports, but this clearance is only satisfied if the antenna is mounted right up to the edge of the case. However, because the case has a curvature to it, it is easy to go too far and mount the antenna so that the corners are bent slightly due to the case's curvature. The bending of the corners can greatly affect the radiation efficiency of the antenna; thus the mounting needs to be very precise.

Adhesive peel.jpg

Affix antenna.jpg

Despite the strong warnings, you won't damage anything if you mount the antenna incorrectly; you will simply have non-optimal RF performance.

Step 4: Snap Case Together

Before starting this step, take a moment to observe that the inner plastic wall of the "HD video in" port has grooves designed to enable the HDMI connector to slide against the plastic wall. Note that the opposite "HD video out" port lacks these grooves.

In order to snap the case together, one must first align and insert the "HD video out" side of the motherboard to the top case. This is the side with the switch, IR jack, and HD video out port. Once this is aligned, you can push the other side of the case in.

See the image below for the alignment order.

Alignment order.jpg

Before pushing the case together, you may need to flex the plastic wall near the HD video in connector. The plastic is designed to handle this kind of flexing. The case should look something like the following the instant before you snap the two halves together.

Correct assembly.jpg

Note that if you reverse the assembly order of the sides, you will apply a traumatic amount of stress to the HD video out connector and the IR extender connector.

Step 5: Affix Retaining Screws

Use the remaining screws to fix the two halves of the case together. If you intend to take the unit apart fairly often, you may omit the screws, as the HDMI connectors and snap hooks do a pretty good job of holding the case together and planarizing the assembly.

Fourblack screws.jpg

Step 6: Affix the Rubber Foot

Peel the backing off of the rubber foot and attach.

Attach foot.jpg

Step 7: Remove Anti-Fingerprint Wrap

If you haven't done so, remove the anti-fingerprint wraps. It is strongly recommend that you do this because otherwise the cooling holes on the top of the case are obstructed.