Difference between revisions of "Fernvale Components"
(→LCD Display) |
(→LCD Display) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 11: | Line 11: | ||
Connector: FPC | Connector: FPC | ||
| + | Reseller in Europe: [http://electronics.semaf.at/ semafelectronics] | ||
Reseller in Europe: [http://www.watterott.com/de/MI0283QT-9 Watterott] | Reseller in Europe: [http://www.watterott.com/de/MI0283QT-9 Watterott] | ||
| − | Reseller in USA: | + | Reseller in USA: [http://www.adafruit.com/products/1774 Adafruit] |
==Camera== | ==Camera== | ||
| Line 28: | Line 29: | ||
Interface: 24pin golden finger | Interface: 24pin golden finger | ||
Size: 19.7mmX12.5mmX6.4mm(customize available) | Size: 19.7mmX12.5mmX6.4mm(customize available) | ||
| + | |||
| + | ==Serial Port (UART)== | ||
| + | |||
| + | The UART connector is similar to the FTDI pinout, but it is only a 5-Pin connector, without RTS(Pin6). | ||
| + | The CTS(Pin2) is unconnected, so RTS/CTS is not available. | ||
| + | Pin3(VUSB) delivers 5V. | ||
| + | It was successfully connected to "uart4" which is /dev/ttymxc3 on Novena by crossing RX(Pin4)/TX(Pin5) and connecting GND (Pin1) | ||
==Battery== | ==Battery== | ||
| Line 35: | Line 43: | ||
==Antennas== | ==Antennas== | ||
| − | Fernvale can use a Bluetooth antenna and a GSM antenna | + | Fernvale can use a Bluetooth antenna and a GSM antenna. Both are using a u.FL (which is also called IPEX) connector. |
| Line 45: | Line 53: | ||
For using Fernvale as an Arduino you might want to use normal Pin-Headers: You need 2 4x1 Headers, and 1 8x1 Header | For using Fernvale as an Arduino you might want to use normal Pin-Headers: You need 2 4x1 Headers, and 1 8x1 Header | ||
| + | |||
| + | ==Headset== | ||
| + | |||
| + | Fernvale needs a CTIA compatible headset. For OMTP headsets you will want to use a CTIA<->OMTP converter. | ||
==Others== | ==Others== | ||
If you find other compatible devices, please list them here. | If you find other compatible devices, please list them here. | ||
Latest revision as of 12:13, 9 June 2015
Fernvale was designed for the following components:
Contents
LCD Display
Vendor: Multi-Inno Product: MI0283QT-11, a 2.83" TFT Datasheet: http://www.multi-inno.com/admin/images/product/20141081959933988.pdf Resolution: 240x320 dots Power: 2.8V LCD Driver: ILI9341 Connector: FPC
Reseller in Europe: semafelectronics Reseller in Europe: Watterott Reseller in USA: Adafruit
Camera
Product: HDF70-TT Vendor: Shenzhen V-Vision Technology Co., Ltd. Sensor: OV7670 CMOS sensor from Omnivision Pixels: HD (UXGA) Top resolution: 640*480 dpi Lens type: 1/6 inch FOV: 65 degree Focal length: 4.6mm F number: 3.0 Distortion: less than 1.0% Interface: 24pin golden finger Size: 19.7mmX12.5mmX6.4mm(customize available)
Serial Port (UART)
The UART connector is similar to the FTDI pinout, but it is only a 5-Pin connector, without RTS(Pin6). The CTS(Pin2) is unconnected, so RTS/CTS is not available. Pin3(VUSB) delivers 5V. It was successfully connected to "uart4" which is /dev/ttymxc3 on Novena by crossing RX(Pin4)/TX(Pin5) and connecting GND (Pin1)
Battery
A 3.7V battery with 3 pins should work which can be found in other mobile phones
Antennas
Fernvale can use a Bluetooth antenna and a GSM antenna. Both are using a u.FL (which is also called IPEX) connector.
SIM Card
Fernvale has a normal Mini-SIM Card holder, for Micro or Nano SIM-Cards you need an adapter.
Arduino
For using Fernvale as an Arduino you might want to use normal Pin-Headers: You need 2 4x1 Headers, and 1 8x1 Header
Headset
Fernvale needs a CTIA compatible headset. For OMTP headsets you will want to use a CTIA<->OMTP converter.
Others
If you find other compatible devices, please list them here.
