Difference between revisions of "Novena ddr3 notes"
(Created page with "==Software support== In order to tune DDR3, a RAM-only version of u-boot was created. This u-boot is totally stripped down to basically an interactive shell with few features. A ...") |
(→2-rank calibrations) |
||
| Line 163: | Line 163: | ||
MPDGHWST2 PHY1 (0x021b4884) = 0x033D0001 | MPDGHWST2 PHY1 (0x021b4884) = 0x033D0001 | ||
MPDGHWST3 PHY1 (0x021b4888) = 0x03630001 | MPDGHWST3 PHY1 (0x021b4888) = 0x03630001 | ||
| + | </pre> | ||
Centon MICU58PIA / CAP1066SO2048.01 (generic POS): | Centon MICU58PIA / CAP1066SO2048.01 (generic POS): | ||
| Line 204: | Line 205: | ||
MPDGHWST2 PHY1 (0x021b4884) = 0x03390001 | MPDGHWST2 PHY1 (0x021b4884) = 0x03390001 | ||
MPDGHWST3 PHY1 (0x021b4888) = 0x035F0001 | MPDGHWST3 PHY1 (0x021b4888) = 0x035F0001 | ||
| + | </pre> | ||
===1-rank calibrations=== | ===1-rank calibrations=== | ||
Kingston 1-rank (1GB magic DIMM) from HP craptop: | Kingston 1-rank (1GB magic DIMM) from HP craptop: | ||
| + | <pre> | ||
Novena U-Boot > tmwcal | Novena U-Boot > tmwcal | ||
Start write leveling calibration | Start write leveling calibration | ||
| Line 250: | Line 253: | ||
MPDGHWST3 PHY1 (0x021b4888) = 0x033001AA | MPDGHWST3 PHY1 (0x021b4888) = 0x033001AA | ||
errorcount: 2 | errorcount: 2 | ||
| + | </pre> | ||
| + | |||
| + | Note above that the errorcount is 2 on this run, i.e., the DQ gating calibration fully succeeded. | ||
==Other Notes== | ==Other Notes== | ||
| Line 277: | Line 283: | ||
significantly, DQS4 is the very last DQS in the fly-by topology chain! | significantly, DQS4 is the very last DQS in the fly-by topology chain! | ||
| − | |||
==Handy Resources== | ==Handy Resources== | ||
Board layout files for SO-DIMMs. Looks like 90% of all SO-DIMMs use the reference design with very, very minor tweaks. There are basically two types of SO-DIMM layouts, one for single-rank, and one for dual-rank. The exception is Samsung, their low power DDR line has a novel layout. | Board layout files for SO-DIMMs. Looks like 90% of all SO-DIMMs use the reference design with very, very minor tweaks. There are basically two types of SO-DIMM layouts, one for single-rank, and one for dual-rank. The exception is Samsung, their low power DDR line has a novel layout. | ||
http://www.jedec.org/standards-documents/focus/memory-module-designs-dimms/DDR3/204-pin%20Unbuffered%20SODIMMs | http://www.jedec.org/standards-documents/focus/memory-module-designs-dimms/DDR3/204-pin%20Unbuffered%20SODIMMs | ||
Revision as of 18:09, 5 January 2013
Contents
Software support
In order to tune DDR3, a RAM-only version of u-boot was created. This u-boot is totally stripped down to basically an interactive shell with few features. A set of calibration access routines were added:
tmd - memory display for tuning tmdel - delay calibration tmrr - read data and checksum from write tmtest - simple RAM read/write test tmw - memory write (fill) for tuning tmw2 - memory write (fill) for tuning, ignores trailing data tmwcal - write calibration tmww - write random data to RAM
Routines like tmrr and tmww just generate traffic to trigger the scope.
tmwcal and tmdel perform the DDR3 calibration routines, per Freescale application notes.
Currently, all the other shell routines break because global/static variable storage is broken. u-boot really tries hard to relocate itself to a new location in RAM, which I don't need it to do. Right now I just jump out of board init and call the interactive shell directly, skipping the board_init_f function which does the relocation. The only thing I'm really missing is hush functionality (which makes up-arrow work) but in the end I decided it wasn't worth the debugging to get that piece working.
To build this special u-boot, do the following.
Check out the tree:
git clone git@github.com:sutajiokousagi/u-boot-imx6.git
Set up the environment (as necessary per toolchain, this is for the OE self-built chain):
source /usr/local/oecore-x86_64/environment-setup-armv7a-angstrom-linux-gnueabi
build it:
make clean; make novena-ramtune_config; make
This should result in a u-boot.imx that is about 80k in size. It's targeted to load into OCRAM at address 0x009073e0. You can grow the image up to about 160k or so in size and it will still work.
burn it:
sudo dd if=u-boot.imx of=/dev/sdX seek=2
This locates the u-boot onto the SD card into the location expected by the initial bootstrapping ROM.
Bringup notes
First, it's important to note that it's impossible to write-level calibrate any memory made by Micron. This is because Micron only mirrors the calibration clock to DQ0 of each memory. However, other manufacturers, such as Kingston and Samsung, mirror the clock to all lanes, allowing for such calibration.
That being said, it was possible to collect calibration runs from several devices.
2-rank calibrations
SN001 samsung M473B5273DH0-YK0 cal:
Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x000C0009 MMDC_MPWLDECTRL1 after write level cal: 0x003A002B MMDC_MPWLDECTRL0 after write level cal: 0x00460052 MMDC_MPWLDECTRL1 after write level cal: 0x004D0101 Novena U-Boot > tmwcal Start write leveling calibration . Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x000C000A MMDC_MPWLDECTRL1 after write level cal: 0x0039002B MMDC_MPWLDECTRL0 after write level cal: 0x00460052 MMDC_MPWLDECTRL1 after write level cal: 0x004D0072 Novena U-Boot > Read DQS Gating calibration MPDGCTRL0 PHY0 (0x021b083c) = 0x4418040F MPDGCTRL1 PHY0 (0x021b0840) = 0x040F0457 MPDGCTRL0 PHY1 (0x021b483c) = 0x45001440 MPDGCTRL1 PHY1 (0x021b4840) = 0x0E000440 Read calibration MPRDDLCTL PHY0 (0x021b0848) = 0x40404040 MPRDDLCTL PHY1 (0x021b4848) = 0x40404040 Write calibration MPWRDLCTL PHY0 (0x021b0850) = 0x2D2E432F MPWRDLCTL PHY1 (0x021b4850) = 0x4736483E Status registers, upper and lower bounds, for read DQS gating. MPDGHWST0 PHY0 (0x021b087c) = 0x02CF0001 MPDGHWST1 PHY0 (0x021b0880) = 0x02D80001 MPDGHWST2 PHY0 (0x021b0884) = 0x03170001 MPDGHWST3 PHY0 (0x021b0888) = 0x02CF0001 MPDGHWST0 PHY1 (0x021b487c) = 0x03000040 MPDGHWST1 PHY1 (0x021b4880) = 0x03400040 MPDGHWST2 PHY1 (0x021b4884) = 0x03000040 MPDGHWST3 PHY1 (0x021b4888) = 0x07C007C0
SN004 Samsung M473B5273DH0-YK0 cal:
Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x00160014 MMDC_MPWLDECTRL1 after write level cal: 0x003F0037 MMDC_MPWLDECTRL0 after write level cal: 0x004E0057 MMDC_MPWLDECTRL1 after write level cal: 0x01040108 Read DQS Gating calibration MPDGCTRL0 PHY0 (0x021b083c) = 0x4425041D MPDGCTRL1 PHY0 (0x021b0840) = 0x04180455 MPDGCTRL0 PHY1 (0x021b483c) = 0x45001440 MPDGCTRL1 PHY1 (0x021b4840) = 0x0E000440 Read calibration MPRDDLCTL PHY0 (0x021b0848) = 0x40404040 MPRDDLCTL PHY1 (0x021b4848) = 0x40404040 Write calibration MPWRDLCTL PHY0 (0x021b0850) = 0x2E324134 MPWRDLCTL PHY1 (0x021b4850) = 0x4737493F Status registers, upper and lower bounds, for read DQS gating. MPDGHWST0 PHY0 (0x021b087c) = 0x02DD0001 MPDGHWST1 PHY0 (0x021b0880) = 0x02E50001 MPDGHWST2 PHY0 (0x021b0884) = 0x03150001 MPDGHWST3 PHY0 (0x021b0888) = 0x02D80001 MPDGHWST0 PHY1 (0x021b487c) = 0x03000040 MPDGHWST1 PHY1 (0x021b4880) = 0x03400040 MPDGHWST2 PHY1 (0x021b4884) = 0x03000040 MPDGHWST3 PHY1 (0x021b4888) = 0x07C007C0
Kingston 2-rank KVR16S11/4 cal:
Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x000F001B MMDC_MPWLDECTRL1 after write level cal: 0x017E003B MMDC_MPWLDECTRL0 after write level cal: 0x00490135 MMDC_MPWLDECTRL1 after write level cal: 0x0061010F Novena U-Boot > tmwcal Start write leveling calibration . Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x000F001A MMDC_MPWLDECTRL1 after write level cal: 0x017E003B MMDC_MPWLDECTRL0 after write level cal: 0x00490135 MMDC_MPWLDECTRL1 after write level cal: 0x0062010E Read DQS Gating calibration MPDGCTRL0 PHY0 (0x021b083c) = 0x44001440 MPDGCTRL1 PHY0 (0x021b0840) = 0x0E000440 MPDGCTRL0 PHY1 (0x021b483c) = 0x4516054A MPDGCTRL1 PHY1 (0x021b4840) = 0x0523047D Read calibration MPRDDLCTL PHY0 (0x021b0848) = 0x40404040 MPRDDLCTL PHY1 (0x021b4848) = 0x40404040 Write calibration MPWRDLCTL PHY0 (0x021b0850) = 0x43414443 MPWRDLCTL PHY1 (0x021b4850) = 0x4633473E Status registers, upper and lower bounds, for read DQS gating. MPDGHWST0 PHY0 (0x021b087c) = 0x03000040 MPDGHWST1 PHY0 (0x021b0880) = 0x02C00040 MPDGHWST2 PHY0 (0x021b0884) = 0x03000040 MPDGHWST3 PHY0 (0x021b0888) = 0x07C007C0 MPDGHWST0 PHY1 (0x021b487c) = 0x038A0001 MPDGHWST1 PHY1 (0x021b4880) = 0x03560001 MPDGHWST2 PHY1 (0x021b4884) = 0x033D0001 MPDGHWST3 PHY1 (0x021b4888) = 0x03630001
Centon MICU58PIA / CAP1066SO2048.01 (generic POS): Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x00120022 MMDC_MPWLDECTRL1 after write level cal: 0x017F0045 MMDC_MPWLDECTRL0 after write level cal: 0x0050013F MMDC_MPWLDECTRL1 after write level cal: 0x00690118 Novena U-Boot > tmwcal Start write leveling calibration . Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x00120023 MMDC_MPWLDECTRL1 after write level cal: 0x017E0045 MMDC_MPWLDECTRL0 after write level cal: 0x00500141 MMDC_MPWLDECTRL1 after write level cal: 0x006A0118 Novena U-Boot > tmdel
Read DQS Gating calibration
MPDGCTRL0 PHY0 (0x021b083c) = 0x44001440
MPDGCTRL1 PHY0 (0x021b0840) = 0x0E000440
MPDGCTRL0 PHY1 (0x021b483c) = 0x45170555
MPDGCTRL1 PHY1 (0x021b4840) = 0x051F0479
Read calibration MPRDDLCTL PHY0 (0x021b0848) = 0x40404040 MPRDDLCTL PHY1 (0x021b4848) = 0x40404040
Write calibration MPWRDLCTL PHY0 (0x021b0850) = 0x43424544 MPWRDLCTL PHY1 (0x021b4850) = 0x36313339
Status registers, upper and lower bounds, for read DQS gating. MPDGHWST0 PHY0 (0x021b087c) = 0x03000040 MPDGHWST1 PHY0 (0x021b0880) = 0x02C00040 MPDGHWST2 PHY0 (0x021b0884) = 0x03000040 MPDGHWST3 PHY0 (0x021b0888) = 0x07C007C0 MPDGHWST0 PHY1 (0x021b487c) = 0x03950001 MPDGHWST1 PHY1 (0x021b4880) = 0x03570001 MPDGHWST2 PHY1 (0x021b4884) = 0x03390001 MPDGHWST3 PHY1 (0x021b4888) = 0x035F0001
1-rank calibrations
Kingston 1-rank (1GB magic DIMM) from HP craptop:
Novena U-Boot > tmwcal Start write leveling calibration . Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x0032003E MMDC_MPWLDECTRL1 after write level cal: 0x0057004E MMDC_MPWLDECTRL0 after write level cal: 0x0050006D MMDC_MPWLDECTRL1 after write level cal: 0x00670108 Novena U-Boot > tmwcal Start write leveling calibration . Write leveling calibration completed, errcount: 0 MMDC_MPWLDECTRL0 after write level cal: 0x0032003E MMDC_MPWLDECTRL1 after write level cal: 0x0057004E MMDC_MPWLDECTRL0 after write level cal: 0x004E006D MMDC_MPWLDECTRL1 after write level cal: 0x00670108 Novena U-Boot > tmwcal Read DQS Gating calibration MPDGCTRL0 PHY0 (0x021b083c) = 0x43400401 MPDGCTRL1 PHY0 (0x021b0840) = 0x04190440 MPDGCTRL0 PHY1 (0x021b483c) = 0x44770300 MPDGCTRL1 PHY1 (0x021b4840) = 0x04700F3F Read calibration MPRDDLCTL PHY0 (0x021b0848) = 0x40404040 MPRDDLCTL PHY1 (0x021b4848) = 0x40404040 Write calibration MPWRDLCTL PHY0 (0x021b0850) = 0x41424644 MPWRDLCTL PHY1 (0x021b4850) = 0x45384A42 Status registers, upper and lower bounds, for read DQS gating. MPDGHWST0 PHY0 (0x021b087c) = 0x02C10141 MPDGHWST1 PHY0 (0x021b0880) = 0x02800141 MPDGHWST2 PHY0 (0x021b0884) = 0x03000141 MPDGHWST3 PHY0 (0x021b0888) = 0x02D90001 MPDGHWST0 PHY1 (0x021b487c) = 0x02400181 MPDGHWST1 PHY1 (0x021b4880) = 0x033701AB MPDGHWST2 PHY1 (0x021b4884) = 0x007F0001 MPDGHWST3 PHY1 (0x021b4888) = 0x033001AA errorcount: 2
Note above that the errorcount is 2 on this run, i.e., the DQ gating calibration fully succeeded.
Other Notes
Measurements performed using TDS5104B 1GHz oscilloscope with dual active P6245 probes:
- probe 3 has about a -5% full scale offset (1.5V reads around 1.45V)
- probe 4 is pretty much dead on
drive strength on A5 looks fine with 60 ohm setting (0x20)
setting of 0x38 improves margin by about 90mV. Tiny overshoot seen. slight improvement in slew rate
conclusion: set to 48 ohm, 0x28 --> looks best here, absolutely no overshoot, signal amplitude matched to clock
dqs7 measured on the dimm side of the termination resistor:
- dimm->cpu rank 0, DQS7 0.36 - 1.19V swing, 830mv total. seems over-driven compared to clock, some reflection seen. in-phase with clock.
- dimm->cpu rank 1 same effect
- cpu->dimm rank 0, DQ7 0.45 - 1.1V swing, 650mV total. a bit cleaner. negative overshoot down to 0.22v seen on leading edge. 180 degrees out of phase with respect to clock.
- cpu->dimm rank 1, same effect
DQS4 is seen as problematic in read/write tests, as evidenced by data patterns:
Novena U-Boot > tmw.l 0xa0000000 0x0000ffff 0x400 Novena U-Boot > tmd.b 0xa0000000 a0000000: ff ff 00 00 3f ff 00 00 ff ff 00 00 d0 ff 00 00 ....?........... a0000010: ff ff 00 00 ba ff 00 00 ff ff 00 00 f6 ff 00 00 ................
significantly, DQS4 is the very last DQS in the fly-by topology chain!
Handy Resources
Board layout files for SO-DIMMs. Looks like 90% of all SO-DIMMs use the reference design with very, very minor tweaks. There are basically two types of SO-DIMM layouts, one for single-rank, and one for dual-rank. The exception is Samsung, their low power DDR line has a novel layout. http://www.jedec.org/standards-documents/focus/memory-module-designs-dimms/DDR3/204-pin%20Unbuffered%20SODIMMs
